Used Race Parts...Cheap !
Guest
Posts: n/a
Used Race Parts...Cheap !
Came across this interesting article.
Roush Racing’s Rejects, At Bargain Basement Prices
Need a place to buy the trickest-of-trick small-block Ford race parts, and for a huge savings over retail ? The bad news is the parts are used. The good news is, the parts were used in Jack Roush’s Winston Cup and Busch Grand National cars. That has two selling points. For one, you can say you’ve got the heads off Mark Martin’s Cup car, if you’re into that sort of thing. Another benefit is that Roush doesn’t use junk and the technology is truly state-of-the-art, especially when it comes to the cylinder heads and intake manifolds. You think your local porter is better than Roush’s boys?
Think again, pal!
Here’s the scoop. Roush runs a bunch of teams in Winston Cup, BGN, and the Craftsman Truck series, and each team has at least two cars. Factor in all the R&D time, qualifier motors, race motors, backups, and other spares, and the Roush teams go through a lot of parts. But here’s the kicker. The parts they relegate to the storage room have not lived their entire useful life. A big-money team like Roush Racing is not about to risk season points and finishing position with a set of rods that have been through a 500-mile race.
But those same rods will probably last forever in the typical 600-800 hp drag race engine—same with crankshafts, valvetrain components, and nearly everything else. An engine is a disposable part of a Winston Cup racecar. At the time of disposal it’s still good, just not good enough to risk in a front-running car.
After a race the engine is torn down and rebuilt, usually with all new parts. And instead of just letting all the killer used parts gather dust for years, Roush sells the stuff (as do most of the big teams) to whomever wants it—be it an underfunded Cup team, or you and I with our drag cars. Think there’s nothing of interest to you and your race 5.0? Consider this. The typical Roush Cup motor is a 358-incher with Yates heads, a matched intake, a killer crank, Carillo steel rods, and Wiseco pistons. Sounds like a good drag race combo, huh? The BGN and truck engines are basically the same, except they run 9.5:1 compression ratios, compared to the 16:1 or 17:1 that the Cup engines run in restrictor plate races (NASCAR rules dropped compression to a max of 12.5:1 in the ‘98 season, however). The truck engines even get to run roller cams, so there’s another used part up for grabs.
Winston Cup teams guard cylinder head and intake manifold technology more closely than the U.S. government guards Area 51. Ask an engine builder flow numbers and port design and he’ll either laugh hysterically or punch you in the mouth. But the escalation of technology and constant research and development make last year’s cylinder heads old news, so the teams don’t care who gets them. Hence, Roush has racks of fully race-prepped heads and intakes up for grabs.
How much for all these goodies? How ‘bout a pair of Yates cylinder heads—professionally ported (we’re talking Winston-damn-Cup-quality porting here!) and reconditioned (with valves, springs, titanium retainers, and a killer valve job)—for $5,000? That may sound high, but ask any racer running Yates heads how much he’s got in ‘em and you’ll faint. The shaft rockers required for these heads are normally about $1,600; Roush’s used parts go for $700. Basically, you can buy used, but very well-prepped, parts for half what they would cost new.
Getting inside Roush to buy the stuff is as simple as calling Red Johnson, the manager of special engines, at (734) 779-7257. Ol’ Red is the guy who keeps track of all the parts and deals with the phone calls. These are all hard-core race parts, so if you’re not serious, don’t waste your or Red’s time. But if you’ve got plans to run eights, or burn up the local circle track, you’ll be hard-pressed to find a better deal on parts of this caliber. And just imagine telling the locals at the track, “Yep, those are Mark Martin’s heads right there. I think they’re the ones that he won with at Martinsville.” Can’t you just see the shock in their faces?
Roush Racing’s Rejects, At Bargain Basement Prices
Need a place to buy the trickest-of-trick small-block Ford race parts, and for a huge savings over retail ? The bad news is the parts are used. The good news is, the parts were used in Jack Roush’s Winston Cup and Busch Grand National cars. That has two selling points. For one, you can say you’ve got the heads off Mark Martin’s Cup car, if you’re into that sort of thing. Another benefit is that Roush doesn’t use junk and the technology is truly state-of-the-art, especially when it comes to the cylinder heads and intake manifolds. You think your local porter is better than Roush’s boys?
Think again, pal!
Here’s the scoop. Roush runs a bunch of teams in Winston Cup, BGN, and the Craftsman Truck series, and each team has at least two cars. Factor in all the R&D time, qualifier motors, race motors, backups, and other spares, and the Roush teams go through a lot of parts. But here’s the kicker. The parts they relegate to the storage room have not lived their entire useful life. A big-money team like Roush Racing is not about to risk season points and finishing position with a set of rods that have been through a 500-mile race.
But those same rods will probably last forever in the typical 600-800 hp drag race engine—same with crankshafts, valvetrain components, and nearly everything else. An engine is a disposable part of a Winston Cup racecar. At the time of disposal it’s still good, just not good enough to risk in a front-running car.
After a race the engine is torn down and rebuilt, usually with all new parts. And instead of just letting all the killer used parts gather dust for years, Roush sells the stuff (as do most of the big teams) to whomever wants it—be it an underfunded Cup team, or you and I with our drag cars. Think there’s nothing of interest to you and your race 5.0? Consider this. The typical Roush Cup motor is a 358-incher with Yates heads, a matched intake, a killer crank, Carillo steel rods, and Wiseco pistons. Sounds like a good drag race combo, huh? The BGN and truck engines are basically the same, except they run 9.5:1 compression ratios, compared to the 16:1 or 17:1 that the Cup engines run in restrictor plate races (NASCAR rules dropped compression to a max of 12.5:1 in the ‘98 season, however). The truck engines even get to run roller cams, so there’s another used part up for grabs.
Winston Cup teams guard cylinder head and intake manifold technology more closely than the U.S. government guards Area 51. Ask an engine builder flow numbers and port design and he’ll either laugh hysterically or punch you in the mouth. But the escalation of technology and constant research and development make last year’s cylinder heads old news, so the teams don’t care who gets them. Hence, Roush has racks of fully race-prepped heads and intakes up for grabs.
How much for all these goodies? How ‘bout a pair of Yates cylinder heads—professionally ported (we’re talking Winston-damn-Cup-quality porting here!) and reconditioned (with valves, springs, titanium retainers, and a killer valve job)—for $5,000? That may sound high, but ask any racer running Yates heads how much he’s got in ‘em and you’ll faint. The shaft rockers required for these heads are normally about $1,600; Roush’s used parts go for $700. Basically, you can buy used, but very well-prepped, parts for half what they would cost new.
Getting inside Roush to buy the stuff is as simple as calling Red Johnson, the manager of special engines, at (734) 779-7257. Ol’ Red is the guy who keeps track of all the parts and deals with the phone calls. These are all hard-core race parts, so if you’re not serious, don’t waste your or Red’s time. But if you’ve got plans to run eights, or burn up the local circle track, you’ll be hard-pressed to find a better deal on parts of this caliber. And just imagine telling the locals at the track, “Yep, those are Mark Martin’s heads right there. I think they’re the ones that he won with at Martinsville.” Can’t you just see the shock in their faces?
AuH20 in '64
Join Date: May 2001
Posts: 6,766
Likes: 0
Received 0 Likes
on
0 Posts
I read about this is Car Craft or Hot Rod, I don't remember which. There is a place that only sells used NASCAR stuff. Be it Chevy, Ford or Mopar.
__________________
U.S. Representative Henry Waxman (D-CA)
“If someone is so fearful that they are going to start using their weapons to protect their rights, it makes me very nervous that these people have weapons at all.”
Originally Posted by XYNaPSE
Article I Section 8 gives Congress the power to do whatever Congress deems necessary.
Red Stripe Beer!
Join Date: Apr 2001
Posts: 192
Likes: 0
Received 0 Likes
on
0 Posts
Any mod motor shit there damn 
__________________
2004 GT: STOCK
1997 GT: Mods: 180 Degree Thermostat, Flowmaster 2 Chambers, MAC O/R H Pipe, MAC Cold Air Intake w/K&N Filter, 75mm Ported Upper Intake w/ 75mm BBK Throttle Body, Screamin Demon Coils with Livewires
1997 GT: has front end damage still drives FOR SALE
AIM:OmFgStFu
2004 GT: STOCK
1997 GT: Mods: 180 Degree Thermostat, Flowmaster 2 Chambers, MAC O/R H Pipe, MAC Cold Air Intake w/K&N Filter, 75mm Ported Upper Intake w/ 75mm BBK Throttle Body, Screamin Demon Coils with Livewires
1997 GT: has front end damage still drives FOR SALE
AIM:OmFgStFu
