Hybrid Motorsports " Nissan Skyline R32 Gtr" Build In Progress
no
Joined: Mar 2007
Posts: 3,328
Likes: 0
^ lol I was thinking the same thing.
Thread Starter
Registered User
Joined: Jul 2008
Posts: 353
Likes: 0
__________________
Hybrid Motorsports LLC.
9470 Ulmerton Rd.
Largo FL. 33773
Unit 3E
Ph. 727.753.9664
Shop Forum: https://www.tamparacing.com/forums/hybrid-motorsports/
Hybrid Motorsports LLC.
9470 Ulmerton Rd.
Largo FL. 33773
Unit 3E
Ph. 727.753.9664
Shop Forum: https://www.tamparacing.com/forums/hybrid-motorsports/
(OO\____/OO)
Joined: Oct 2008
Posts: 5,612
Likes: 0
here... i'll help again... takes 5 seconds....
Paint:
Abs w/hardlines, Engine harness,
Abs/ hardlines, engine harness, brake master, clutch master etc. installed
Ecu's installed: Mines / Hks fcon v pro:
Installing chassis harness:
A few more components then we can wash/degrease down the e-bay, in preparation of the engine.
In the next segment, we'll move on to engine! Catcha later, and thanks for checking us out!
Paint:
Abs w/hardlines, Engine harness,
Abs/ hardlines, engine harness, brake master, clutch master etc. installed
Ecu's installed: Mines / Hks fcon v pro:
Installing chassis harness:
A few more components then we can wash/degrease down the e-bay, in preparation of the engine.
In the next segment, we'll move on to engine! Catcha later, and thanks for checking us out!
FN Herstal
Joined: Jun 2007
Posts: 1,612
Likes: 0
Doesnt see what you did
Joined: Sep 2007
Posts: 3,683
Likes: 0
Just a tip for whoever spliced that giant cluster of wiring back together, if that wasnt all sliced in that one spot, and just a oh we got to fix it repair, you can have things turn out much better by offsetting each connection just a little bit, so you dont end up with 20 connections in one spot making for a bulge in the harness.
Yeah, tims just a genius, he's so talented, he's managed to bolt a run of the mill engine, into a run of the mill car, and praise himself so much for it. He's my hero.
Yeah, tims just a genius, he's so talented, he's managed to bolt a run of the mill engine, into a run of the mill car, and praise himself so much for it. He's my hero.
(OO\____/OO)
Joined: Oct 2008
Posts: 5,612
Likes: 0
that
when i redid my harness, i took out that extra 2ft of RHD wire, and soldered/heat shrunk all the wires in one spot, i ended up with a twisted lump, not entirely bad, but reading what Z28 said, i kinda wish i went that route...
still tucked behind the head, so you couldn't see it, and it's not on my car anymore anyways.... so w/e...
Thread Starter
Registered User
Joined: Jul 2008
Posts: 353
Likes: 0
Updated segment: link to full thread: https://www.tamparacing.com/forums/h...-re-paint.html
We'll move to the engine, While we wait a some new hardline for the car.
Just to give this engine a bit of punch while we fully build our spare block.
We'll begin by removing & replacing the stock twin turbo units & stock clutch.
Ahhhhhh what a mess well lets begin:
Thers's 40+ pounds of nissan goodness........ yeah right
In the next segment, we'll move on to turbo, clutch, etc!!! Catcha later, and thanks for checking us out!
We'll move to the engine, While we wait a some new hardline for the car.
Just to give this engine a bit of punch while we fully build our spare block.
We'll begin by removing & replacing the stock twin turbo units & stock clutch.
Ahhhhhh what a mess well lets begin:
Thers's 40+ pounds of nissan goodness........ yeah right
In the next segment, we'll move on to turbo, clutch, etc!!! Catcha later, and thanks for checking us out!
__________________
Hybrid Motorsports LLC.
9470 Ulmerton Rd.
Largo FL. 33773
Unit 3E
Ph. 727.753.9664
Shop Forum: https://www.tamparacing.com/forums/hybrid-motorsports/
Hybrid Motorsports LLC.
9470 Ulmerton Rd.
Largo FL. 33773
Unit 3E
Ph. 727.753.9664
Shop Forum: https://www.tamparacing.com/forums/hybrid-motorsports/
